Electrolux and Westinghouse Washing Machine Error Codes E10, E20 and E40

On an Electrolux or Westinghouse washing machine, E10 means the machine is not filling with water as expected, E20 means it is not draining, and E40 means the door is open or not closed firmly. Each code starts with checks you can do yourself, and none of them on its own shows that a part has failed.
Electrolux and Westinghouse share a support platform, but a code table for one model is not a table for every model. Use the model and product number from the rating label, and where your manual and a general page disagree, follow the manual.
The causes below follow the order in the manufacturers' troubleshooting steps, easy owner checks first. The manuals do not publish failure rates, so this is a checking order and not a ranking of what fails most.
Quick reference
| Code | What it means | Owner check | When to book |
|---|---|---|---|
| E10 | Not filling, or difficulty filling | Tap fully open, inlet hose not kinked, drain hose installed as the manual says, inlet filter cleaned with power and water off | E10 returns with supply and hoses clear |
| E20 | Not draining, or difficulty draining | Program (rinse hold), drain hose, sink connection, owner-accessible filter | E20 returns after the drain path is clear |
| E21 | Front loader not emptying and/or not spinning (Westinghouse front loader support) | Same checks as E20 | Persists after the drain checks |
| E40 | Door open or not firmly closed (Electrolux EW1080F manual) | Clear laundry from the door, close it firmly | Persists with the door correctly closed |
Sources: the Electrolux Australia EW1080F manual, the Electrolux support articles for E10 and E20 on Westinghouse top loaders, and the Westinghouse support page for E20 and E21 on front loaders.
Safe isolation before you touch anything
Stop the program. Switching off at the control panel is not the same as unplugging, so unplug before any cleaning. Turn the water tap off before you disconnect an inlet hose, and let wash water cool before you open a pump filter. Do not touch the plug or socket if water has reached it. Energy Safe Victoria advises that only a qualified repair technician or licensed electrician should repair faulty electrical appliances.
E10: the washer is not filling
The EW1080F manual describes E10 as no water filling. The Westinghouse top loader support page describes it as difficulty filling for washing.
The causes, in checking order:
- A closed or partly closed tap, or low water supply.
- A kinked or squashed inlet hose.
- A blocked inlet hose filter.
- A drain hose that is not installed as the manual requires. On the EW1080F, a door that is not properly closed is also listed.
- An inlet valve, pressure sensor, wiring or control board fault, once the above are ruled out.
Check that the tap is fully open and that the hose is not crushed behind the machine, without dragging the washer against its connections. On a Westinghouse top loader the support page also asks you to check the drain installation: the top of the drain hose should be above the join between the cabinet and the top, so a fill complaint can be an installation fault and not a faulty valve.
To clean an inlet filter, unplug the washer and close the tap first, expect some water to spill, then reconnect the hose securely, reopen the tap and check for leaks before running a cycle. Valve replacement, pressure sensor work, wiring and board repairs are not owner jobs. If E10 comes back with the supply and hoses clear, book a technician instead of buying a valve on the code alone.
E20 and E21: the washer is not draining
The EW1080F manual says E20 means the water is not drained. Westinghouse's top loader support page calls it difficulty draining for washing, and its front loader page groups E20 and E21 under a machine that does not empty and/or does not spin.
The causes, in checking order:
- A program or option that holds water. The EW1080F manual lists Rinse Hold.
- A kinked, squashed or blocked drain hose, or a blocked sink spigot or household drain.
- A clogged filter or pump chamber, on models where the owner can reach it.
- A hose connection or installation height that does not match the manual.
- A drain pump or drain valve, pressure sensor, wiring or control board fault.
If the washer drains into a laundry sink, check that the sink empties normally. Westinghouse tells owners to check the sink spigot before they get to the pump filter. A blocked household drain looks like a pump fault from the outside and calls for a plumber, not a new pump.
To clean an owner-accessible filter, unplug first, wait until the water is cold, lay towels and put a container under the filter, and follow the draining procedure for your model. Do not unscrew a filter on the assumption the drum is empty. Cleaning a filter the manual describes is maintenance. Removing or replacing the pump is repair work, and so are pressure sensor, wiring and board faults. Our guide to a washing machine not draining or spinning covers the same symptom across brands.
E40: the door is open or not closed firmly
On the Electrolux EW1080F, E40 means the door is open, and the instruction is to make sure it is firmly closed. The Westinghouse WWF1044M7WA front loader manual likewise tells owners to close the door firmly when it is open or incorrectly closed.
Stop the program, look for laundry caught in the door or seal, and close the door normally. Do not slam it, force a locked door, or bridge or bypass a door or lid switch. Unplug before you clean around the latch.
A damaged latch or hinge, or a door that stays unrecognised when it is properly closed, needs a technician. The door lock is part of the machine's safety system, and Westinghouse says not to operate a washer with a missing or faulty door or lid. The code does not separate a mechanical fault from an electrical one.
E40 is a front loader door code on the manual we checked. A top loader has a lid, and the WWT1284M7WA manual tells owners to close the lid and press Start/Pause without tying that to E40, so do not carry the front loader meaning over to a top loader.
Other codes: E30, E11 and E13
These vary by model, so read your manual. The Westinghouse WWT1284M7WA top loader manual groups E30 with a pressure sensor fault, pressure sensor calibration and water overload, and lists the sensor, inlet valve, drainage, pump or drain valve, wiring and main board as possible faults. If water is rising too far or escaping, stop the machine and close the taps. Calibration, sensor and internal valve or pump work is for a technician. E11 and E13 appear in some Electrolux technical documents as a filling difficulty and a leak, but we have not confirmed them for a particular Australian model, so do not order a part on those codes.
Who does which job
Taps, program selection, door closing, hose routing and cleaning a filter your manual describes are owner tasks. Replacing a pump, inlet valve, pressure sensor, door lock or control board is a job for a qualified appliance technician. A faulty power point or fixed wiring is for a licensed electrician: electrical wiring work in NSW must be done by a licensed electrician.
Booking an Electrolux or Westinghouse washer repair
We are an authorised repairer for Electrolux and Westinghouse and repair washing machines across Wollongong and the Illawarra. Have the model and product number, the full code on the display and what you have already checked ready. If the machine also stops mid-cycle, see washing machine won't start, and for the brands we see most in the area see appliance brands in the Illawarra and what fails. You can book a repair or call 02 4229 3777.




